I've increased the limit to 40 pictures per post (to accommodate one of my own trip reports).
-
Happy Birthday, Thomas Edison (1847-1931)! ⚡💡📽️
Kite +6%
- Thread starter BigandSmall
- Start date
I've increased the limit to 40 pictures per post (to accommodate one of my own trip reports).
Glassed the front side of the float tank pieces. Hung the glass over edge for weight to help it make the corner.
Three coats on the patch, first one with a Bondo scraper then two more with a roller. Started sanding the bow tumblehome section. Starting to feel like the home stretch.
Three coats on the patch, first one with a Bondo scraper then two more with a roller. Started sanding the bow tumblehome section. Starting to feel like the home stretch.
After doing some sanding around the edges to get everything lined up properly I put 4 big globs of hot glue to lock the vertical piece in place.
While the glue was cooling off and strengthening up I went to work feathering out the patch I put in.
I taped a seal/dam around the front face then made a filet joint with a mixture of wood flour and 410 microlight. I cleaned up the joint with a disposable spoon then put a bunch of pieces 4 oz s-glass scraps cut to about 1.5"x4". I stuck them all into place then wet them out with a paint brush.
I didn't get any pictures of the next part since I was rushing a little working against pot life. I was using some old epoxy on the inside. It still sets up nicely but it's a little yellow. I wet out all around the the small cedar bead I had hot glued in place to be a shelf for the top plate. I then got some new expoy and mixed it with just wood flour. Using the icing bag I put a bed along the top of the bead shelf. I then slid the top plate into place and gave it a wiggle and few taps settling it in and seeing the schmutz come up the outside a little. I put tape with tension on it to try to close the gap and level it as much as possible. I still need to glass the joint between the pieces and do a filet joint around the whole thing but it feels pretty permanent.
While the glue was cooling off and strengthening up I went to work feathering out the patch I put in.
I taped a seal/dam around the front face then made a filet joint with a mixture of wood flour and 410 microlight. I cleaned up the joint with a disposable spoon then put a bunch of pieces 4 oz s-glass scraps cut to about 1.5"x4". I stuck them all into place then wet them out with a paint brush.
I didn't get any pictures of the next part since I was rushing a little working against pot life. I was using some old epoxy on the inside. It still sets up nicely but it's a little yellow. I wet out all around the the small cedar bead I had hot glued in place to be a shelf for the top plate. I then got some new expoy and mixed it with just wood flour. Using the icing bag I put a bed along the top of the bead shelf. I then slid the top plate into place and gave it a wiggle and few taps settling it in and seeing the schmutz come up the outside a little. I put tape with tension on it to try to close the gap and level it as much as possible. I still need to glass the joint between the pieces and do a filet joint around the whole thing but it feels pretty permanent.
I put a patch over the seam with a couple of fill coats. I also drilled an oversized vent hole at the top of each tank. When I did the fill coats I dripped some epoxy in the vent holes sealing them up. I'll drill a pin hole in the center after varnish. I made a mistake by forgetting to remove the masking with each coat and shift it down. I wound up with quite a ridge but it sanded out easily enough.
I feathered out the patch then mixed up some epoxy with straight wood flour and put a thin bead around the outside of the float tank. I used the handle end of a wood spoon on the vertical and the end of a coffee stir stick up top to clean up the fillets. Once they've hardened I'll lightly sand them and go over them again with epoxy to help seal and make them smoother to the touch.
Before work tonight I got my wife to help me flip the boat over and I started level sanding the outside. I sure like that long board with the 80 grit abranet.
I feathered out the patch then mixed up some epoxy with straight wood flour and put a thin bead around the outside of the float tank. I used the handle end of a wood spoon on the vertical and the end of a coffee stir stick up top to clean up the fillets. Once they've hardened I'll lightly sand them and go over them again with epoxy to help seal and make them smoother to the touch.
Before work tonight I got my wife to help me flip the boat over and I started level sanding the outside. I sure like that long board with the 80 grit abranet.
