Search results

Same here. I just logged in to add to this thread

Try this https://www.austinkayak.com/products/9717/Harmony-54-inch-3D-End-Float-Bag-Vinyl.html

No arm rests, no reclining, but it packs up small and has back support. Best of all the seat height is positioned just high enough that when you want to get up, you simply stand - no need for a two arm push off. Been my camp companion for 10+ years...

Correction. On that trip I was in my Wenonah Advantage which is a hard tracking canoe so the Clipper of course turned easier. If Mike is correct on 1 1/2 inch rocker then the Clipper might handle wind issues reasonably well in the hands of a practiced paddler. In the canoe it felt like a fine...

This was a 100+ mile multiday trip so he's carrying a tripping load. And I agree with Mikey, it did feel like a big boat despite it being a small canoe

For what it is worth, I had the opportunity to spend an hour in one on some moving water and found it to be quite a nice canoe. More rockered than the canoe I was using so it spun a little more quickly than my canoe (OT Cascade). Without some good paddle skills I imagine it could be...

1 cup at a time, this coffee press is my preference these days. Makes a consistently excellent brew. Slightly bulky to pack, but worth it for me...

And a third way to set those handles.

GPS worked well in that location. The Garmin unit let us paddle a big circle through swamp

You can get intimate here to the point of becoming quite lost.

On the PFD, blunt end Rescue knife, whistle, strobe/SOS light In the pockets - small sunscreen, lip block, about 15 yards of duct tape rolled around a small diameter section of pvc pipe, compass, signal mirror, small waterproof note pad with golf pencili in the spiral binding, one energy bar...

I thought about the benefit of xtra wood along the gunwale, but at the end of the canoe is it that important? Drilling the longer hole in narrower stock wasn't an issue for me - I have a portalign drill press guide. I may have dropped down to a #8 machine screw. The feel to my hand when...

Your carry handles do look bad and would be replaced if it were my canoe. A number of years ago I added carry handles to an older canoe. Bought the handles from Ed's Canoe and they are shaped much the way yours are, a curve cut into the square stock where you would place your hand. I...

My understanding is epoxy resin is UV sensitive and w/o a covering will fail on some level. So I've always either added carbon or enamel spray painted epoxy finishes in my interior repairs. I'm not sure how sensitive epoxy is to light, but I don't want to set myself up for another repair some...

Here is what I use. It is pretty water resistant, but not totally waterproof. Anything that really needs to be dry, I ziplock or small dry box it. Very well made. I like the d- rings that let me attach my map case to it for easy access. And I have used the cutting board for cutting fresh...

The clean aluminum gunnels of my new ultralight canoe spent quite a trips on the bare, black metal rack of friends vehicle. Left ugly black marks in several locations. I cleaned it up by usin 220 grit sandpaper on a random orbital sander, and feathered in the edges with 0000 steel wool. Came...

I know some WW paddlers have installed elec pumps to empty their boats on wet rides. Do any of you lake paddlers have a similar setup? Far from shore, I imagine that could be really useful on a big wave day.

A nice matte enamel paint could be a solution. The hardest part is the taping job; a wheeled shop stool really, really takes away a good part of the effort. I chose brush/roll on over spray. Thought it might be more durable and touch ups are easier. I went to my local paint store and they...

Yup, take control of your images and buy an external hard drive. Here is a 2 terabyte HD for about $70; get a 3T for a little over a hundred. If you are paying $25/year for cloud storage you'll recover your investment in 3 years, plus you have control...

This thread may help you. I rehabbed a gel coated, aluminum gunnel Swift several years ago. You may want to closely examine the rivets on the aluminum gunnels. Salt marine environments can be tough on metals...