• The 2026-29 Fund Drive needs 15 MORE DONATIONS to reach target. Read the Featured Thread for details. Please donate!!!

Search results

  1. Thestripper

    In praise of cheap binoculars.

    I have had to use Vortex warranty on three occasions and they stand by their word. With the lower price products from them you can expect to use this warranty sooner rather than later but their higher priced segment has some good products. Swarovski has a very similar mentality when it comes to...
  2. Thestripper

    In praise of cheap binoculars.

    I've gone through a bunch of binoculars, both expensive and modestly priced ones and I love to use them all. My advice is to buy one pair that is expensive and then be happy for the rest of your life because that's how long they will last, and then some. The more known high-end manufacturers...
  3. Thestripper

    The New Swift/DY Redesign of the Dragonfly

    I haven't seen one in the flesh so I can't say anything about their finish however, Merrimack canoes are probably the most beautiful modern canoes out there, or at least arguably so. No wait.. they are! I belive some of the other manufacturers might have the edge when it comes to progressive...
  4. Thestripper

    The New Swift/DY Redesign of the Dragonfly

    Do you mean that handle looking thing? Swift calls it a: "Carbon Assist Bar - This support bar is designed to help a paddler get up from a seated position in a boat or as the ultimate handle for portaging." Next big thing could be a thwart handle-handle, so you don't have to grab the thwart...
  5. Thestripper

    The New Swift/DY Redesign of the Dragonfly

    I honestly think that SuperFly would have been a better name for it. Or SpanishFly..
  6. Thestripper

    The New Swift/DY Redesign of the Dragonfly

    Hi Glenn. Thanks for putting together the comparison. It's clear to see that the new Dragonfly has been changed so much that they should also have given it a new name. They seem to have a knack for reusing other models names though. Why this is I don't know but there can't be any good...
  7. Thestripper

    The new Swift Cirrus canoe

    Annoyingly, Swift names their new canoe "Cirrus" when there already is a canoe model named Cirrus. What makes matters worse is that Swift even had that first Cirrus in their lineup -the John Winters - Cirrus 18'. I'm actually more curious about the Cirrus 18' which looks like a much more...
  8. Thestripper

    How Does David Yost Build His Plugs…?

    This was a great interview with DY. Around 23 minutes in you get to see the prototype up close. Looks like he is using a inside keel (!)
  9. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    The pictures I posted are from the offsets in Canoecraft, those are not from your file and there is no automation in this case so there is no right or wrong order. What I was trying to show was how bad the results are when automating -curve through points- as opposed to drawing a curve manually...
  10. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    The reason I ask what method you use to make your curves is that I'm not getting good results when automating this. Simply put, a fair curve will not fit through the points from the table of offsets. Playing around with different degree curves and/or chord settings can make it better but it will...
  11. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    Well.. I did now and everything is there. I just didn't see it at first :sneaky:
  12. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    Thank you for that explanation! I think I will try your method if only I can wrap my head around what you are doing. That link you posted can't be the coordinates for a whole canoe since it's only 18 rows in two columns. If I understand it right those are the coordinates for only one station...
  13. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    Hi Kliff. Could you explain how you went about this in more detail?
  14. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    Hi. Oh I didn't see that you had also found the Station 1 correction. But that's good. Twice confirmed then. The station 0 correction that I did is just a small adjustment. Pretty obvious once you get the rest of the points for that station down on paper and eye it. The sheer point is pretty...
  15. Thestripper

    Lofting Canoe Molds from CanoeCraft tables

    Hi Cruiser. This is great! I have almost finished plotting out all the points for the Freedom 17 (I'm doing it digitally). My table of offsets comes from Canoecraft Twelfth printing 2019. I've found one point that seem to be off in the Table of Half-Breaths. Just wanted to check if you ran in to...
  16. Thestripper

    An extra trippy Merlin canoe strip build

    Maybe it's not so bad after all? How much distance do you have at station #13 when just holding the strip with your hands (or using tape)? Maybe you could get away with slight fairing on station #12 and #14 instead of building up #13? Or maybe a combination. You would probably need no more than...
  17. Thestripper

    An extra trippy Merlin canoe strip build

    Gamma. I don't know if this is just how you rigged that test strip up to take this photo or not, but when you clamp the strip like that it "re-curves". This is not the way the strip lays on the hull naturally. When clamped like that it will pivot over the first station and therefor "fly" past...
  18. Thestripper

    An extra trippy Merlin canoe strip build

    Maybe this comparison should have gone in a separate thread but just to wrap it up. Yes, I think that they do come from the same source which probably is the Kunz original Merlin. If the keel line of the NWC Merlin was flattened then it looks like they would be near identical under the...
  19. Thestripper

    An extra trippy Merlin canoe strip build

    Hi Jim! Is it really true that you will get the 38 Spl. by scaling the NWC Merlin plans? A wise man once told me that the North West Merlin was not the parent of the 38 Spl. That the the 38 Spl. was a Bruce Kunz creation and that It was an enlargement of Bruce's original Merlin. I've laid the...
  20. Thestripper

    How Does David Yost Build His Plugs…?

    I'm also very curios and want to know more about the design and development. I don't know what kind of wood they use for the Swift prototypes but I have seen that at least some of the prototypes have been built with stems and those were laminated from what looked like 1/4" or thinner pieces but...
Back
Top Bottom