Search results

I hope it helps. I used the table saw on my first build, and it did good, but the boards had to have 2 square sides. I used saw mill lumber, very uneven and far from square. All that didn't matter as much with the skil saw method. With a little attention when ripping, the strips were very...

Thanks for the advice. I saw the Interlux brand when I was researching yesterday. I used the US Composites resin on the first build. It had a lot of blushing, I scrubbed my butt off with dish detergent and scotch Brite pads. This recent canoe, I used RAKA. Very little to no blushing...

No sir, it's a 15 amp metabo. I'm live on the cheap stuff, inexpensive stuff I mean.

I used a Minwax spar urethrane on my first canoe build, 4 years ago, and it held up very well. But not so on my recent build. I used the same on my Raven, but something is different. I took it out this morning The wind was challenging to say the least, but I bumped a rock coming in. Eh no big...

I like the skill saw setup also. Not my best look, but it is quick and easy, well other then my trying to get my back to straighten up afterwards. Looking forward to following along. Roy

Your bow and stern stem forms should be tapered like this I doubled up the stem form thickness and sanded the edges so the strips would lay flat on the edges. I this helps. Roy

I just finished my 2nd stripper. I used mainly, sawmill, air dried poplar 50 cents/bdft. -70$ skill saw to cut strips. -An inexpensive used router 50$ with a home made router table, nothing fancy. - orbital sander 70$ - pull saw, under 20$ which I use a lot. - Jig saw under 50$. A person can...

My wife said it was a little low in the stern...😏 Uh huh. I told her I could gain about 60 more pounds and still be ok.

This is where I was working around the chine. I started at the shear line.

Looking good👍 I struggled a little coming around the chime on mine also. I think it's just one of those things. Mine came in about 60#. The poplar wood I used was about 32lb/ft

Here's the pictures wife took

I don't know if this will work. I finished the Raven canoe and took it out for a short paddle. It is a lot more responsive then the Wabnaki I made. It has lots of room for plenty of gear. I took it the local lake that has been drawn down to winter pool, so it's not a very scenic area. I'm very...

Thank you.

I was working on an idea for a brand. It didn't quite work out like I expected. Next time I'll do it on the computer. I didn't realize I left my finger prints behind. I figured if I ever get the chance to make it up north to Canada for an extended trip in the wilderness, maybe some one can...

The inside is finished. I've got another coat of varnish to put on the exterior, and it'll be done. I milked this build out for several months and I have enjoyed it. The weather is warming up and I'm getting anxious to see how this design does.

There is no way I would have put a video of my stupidity out there. I don't even clutter up my fish and ski motor boat like that. Things should have been strapped in, out of the way and I would've been on my knees for better stability and/or praying. Why do people think it can't happen to them...

I put the seat back 10" from center. I sit more then I kneel, and my belly may hang far enough out... I think the seat in my little 13 solo Mohawk sets about 6 inches back, and it seemed a little close. Roy

Ready to go! I love it. I never take the time to do test stuff. I know I should. Great job on test panels. Roy

Lots of finish sanding on the deck plates and gunnels. I urethaned the seat webbing I need to drill a drain hole in each end of the canoe, so water can drain out when flipped upside down. I thought maybe to drill an angle through the inner stem Instead of drilling through the center of the deck...